In Case You Leave Auto Repair To A Professional Mechanic? Every car fails
sooner or later, and that's a well known fact! With that in mind, some cars are more prone to malfunctioning than others, of course, if you're in a tough situation, you may well be left to wonder: can i attempt a DIY auto repair or work with a mechanic? An oil change is a great instance of something even a novice driver could do, but if you have problems beyond that, acquiring a car mechanic to complete the repairs can be quite a good plan and here's why: Experience You may have virtually no idea what you're doing and you could actually end up making things worse. Even if you feel like you're a DIY savvy person, you could end up causing other areas of your own car to malfunction. Along with, you simply have no idea what's actually wrong with the vehicle, except if you bring it apart and hope with your might you are able to use it back together again again. A car mechanic is doing this for many years and he can easily diagnose and repair any issue your car may be against. Right Tools You require the proper tools and a decent workspace to start working on auto repair. Until you have a complete garage with equipment and tools committed to this, you will have to spend money on the necessary tools to correct your car. Needless to say, without prior experience coping with car repair, you might not know what you need to purchase, not forgetting, you might never start using these tools again. Hiring a professional car mechanic can eliminate the demand for you to invest money into equipment and tools you're unlikely to work with again because he will already have everything accessible. Speedy Repairs In the event you only have one household car you need to use to get to focus on time, you need to ensure your car is fixed at the earliest opportunity. Obviously, when you attempt a DIY repair, things will go wrong, as well as after they don't, it can take you plenty more time to have your vehicle running than if you work with a mechanic. Maybe you have your automobile away from commission for a couple of days when taking it to some mechanic, however it sure beats being unable to start working! Spend Less Perhaps one of the most compelling reasons to drop your car off for repair in a mechanic's is to spend less. You won't need to invest money into tools, equipment, and auto parts you may never need. Along with, while your vehicle has run out of commission, you may have to rent a car or consider the bus-- costing you more cash! Working with a mechanic for auto repair could help you save inside the long term, particularly if take into account that a job well done can prolong the lifespan of your respective vehicle. Next time your automobile gives you trouble, why not stop at the car mechanic's?
Local Time in Kingman |
Wikipedia Information About Kingman |
Google Map of Kingman
Youtube Video's of Kingman |
Info from Wiki on Vehicle Service
FAQ's Auto Repair
Could There Be More Problems With This Ford Bronco 10 Best Vehicle Service in Kingman Directory?
Tomorrow I Am Going To Look At A 1989 Ford Bronco That A Guy Was Advertising On Craigslist. I Called Him And He Told Me That The Only Problems It Has Are A Mistimed Ignition And It Needs A Couple Freeze Plugs Replaced.
Basically I Need To Know If It Could Possibly Have Worse Problems That He Is Trying To Pass Off As These Less Serious Ones. What Should I Look For?
Yes, very well have more problems, with ign off as he claims could use this to hid compression problems and timing chain issues, freeze plugs could hide head gaskets or other things that make it overheat. But he could be shooting straight, most times people selling cars don't. Top Ten Vehicle Service in Kingman Directory
How Do You Figure The Cubic Inches Of My Engine?
Ok I Have A Ford 460 In My 79 Bronco But Its Built Pretty Good And After A Recent Head Gasket Replacement I Checked The Bore And It Turns Out Its Bored 30 Over So What Does That Make My Cubic Inches Best Ten Vehicle Service in Kingman Directory?
that's why the online calculators are so nice..
Volume equals pie times the Radius squared times the stroke times the number of cylinders equals 467 rounded off. Best Ten Vehicle Service in Kingman Directory
that's using 0.030" over
Ford Contour 99, Runs Very Bad. Most Popular Vehicle Service in Kingman Directory?
I Have A Ford Contour 99, I Did Replace The Timing Belt, Idler Pulley, And Timing Adjuster. Now After That It Run A Little Rough, So I Decided To Use For Some Time, Now Is Worse, I Did Re-Set Timing Following Ford Instructions, 1 And 4 Cylinder At Tdc, Cams Aligned With Flat Steel Tool, Cam Sprockets Loose, Timing Belt Tight All The Way Around, Re- Started And Runs Very Bad, Shakes, Misses, All Kinds Of Things. No Smoke At Tailpipe, Then I Checked The Compression, It Was Very Low, Almost Cero.. My Question Is: Can My Timing Be Off To Not Having Any Compression At All≫? Or Could I Have A Burned Valve, Or A Piston/Valve Collision, (Acording To Ford,Is Not An Interference Engine,[2.0 Liter] ) Any Suggestions≫?, I Almost Throwing My Towel, And Don'T Know What Can Be The Problem.. Did Replace Sparks, Coil, Sparks Cables, Checked My Injectors, No Vacuum Leaks, Thank You For Any Good Help.
A stock Zetec is non-interference unless it's a SVT or has been modified (high lift cam). If the timing is way off, then you won't have compression, but it sounds like you are doing it right from what I can gather. However, in some cases non-interference engines can get bent values due to carbon buildup on top of the cylinders, especially in the valve reliefs (reduces valve clearance). There are some rare cases of this occurring with the Zetec.
To test the valves, you can do a leak down test on the cylinders. Basically you shoot compressed air in through the spark plug and see if the pressure in the cylinder drops. In your case, if you have bent valves you should be able to hear a decent "hiss" in the intake or exhaust. You can also try testing the compression with the timing belt off and both valves closed (rotate camshafts). Best Ten Vehicle Service in Kingman Directory
Burnt valves are also a possibility, but you would have noticed this before the belt change. It is also unlikely all four would be burnt and giving zero compression.
Just to be sure, cylinder #1 is the one closest to the timing belt. Also, did you double check your plug wiring? Try to be as precise as possible with TDC in #1, otherwise you could be a tooth or two off.
You said no vacuum leaks, but did you check the EGR, IAC, and MAF? These can all cause roughness.
If all else fails, you can pull the head and see what it looks like inside. Might as well replace the head gasket (order after you see the condition of the valves).
Here is another how to, maybe a different source will help: http://www.contour.org/ceg-vb/showthread...
Hope you can figure it out! Best Ten Vehicle Service in Kingman Directory
Car Issues...Blown Head Gasket And Antifreeze Leak Most Popular Vehicle Service in Kingman Directory?
I Have A 1997 Ford Contour Gl With Almost 112Kmi. Last Week When I Was Driving The Car At 55 Mph The Car Started Lurching Forward...Kind Of Like How It Feels When You Just Tap On The Accelerator And It Jumps Forward. I Pulled Over And Turned The Car Off To Check For Leaks And A Flat Tire, Nothing Happened. Went To Turn The Car Back On (Worked) And Started Driving Home...Which Was About Half A Mile. As Soon As I Started Driving (20 Mph) The Front Of The Car Started To Shake Really Bad (Is Not The Alignment), Made Groaning And Whaling Noises, And Would Not Accelerate Above 25 Mph. When I Finally Made It Home I Turned Off The Engine, Went To Call My Mechanic, And He Told Me To Turn It Back On But It Wouldn'T Start. I Have To Wait Two More Days Until I Can Get The Car Looked At But In The Mean Time I Tried To Jump Start The Car To See If It Would Start. It Took About 3 Tries And Then Just Letting The Car Charge From My Moms Car And It Finally Worked. Now The Car'S Exhaust Is Spewing White And The Antifreeze Is Brown/Rusted But Not Too Low. It'S Also Idling Really Rough And Over Heats Within A Minute. I Have Never Missed An Oil Change, So That Isn'T The Issue. I Also Have An Over Heating Issue And My Temp Gauge Isn'T Registering It (I Think That'S Just Broken). I Just Want To Know If Anyone Else Has Had This Issue Or Knows What It Could Be. I'Ve Been Told It May Be A Blow Gasket And An Antifreeze Leak Into The Oil. Wanted Some Opinions Before It Gets Looked At In 2 Days. I'M Trying To Figure Out If It Is Too Bad A Fix And If I Should Just Get A New Car. Please Do Not Answer This If You Have No Intention On Giving Me Advise For What May Be Wrong With The Car.
yes sounds like the head gasket but also could be the intaake manifold gasket and my advise is to buy a new car 10 Best Vehicle Service in Kingman Directory
What Should I Do With My Car Top Ten Vehicle Service in Kingman Directory?
I Asked A Question Not Too Long Ago About My 1997 Ford Aspire With 121K Miles, Which Had A Misfire In One Of Its Cylinders When I Bought It. Now I'Ve Got Several More Questions. Here'S The Story:
I Took It To A Reputable Repair Shop And Had It Diagnosed The Other Day As A Pretty Serious Problem, Which Was Most Likely A Malfunctioning Valve, Though They Would Have To Take Apart The Cylinder Head To Confirm That. They Based Their Evaluation On The Fact That The 3 Healthy Cylinders Were Putting Out 170 Pounds Of Pressure While The Other Was Putting Out 80 Pounds. When I Talked To Other Mechanics They Said They Would Expect A Valve Problem Too With Those Numbers. I Have An Appointment Set For Monday Morning To Get The Cylinder Head Taken Off So That The Mechanics Can Find Out What The Problem Is Exactly.
The Previous Owner Knew For Some Time That The Misfire Existed, But He Assumed That It Was Because Of The Spark Plugs, Which Are Pretty Worn. After I Bought The Car And Drove It Around A Bit, But Before I Took It To The Mechanic, The Check Engine Light Came On And Remained On Until Earlier Today When It Shut Off.
Here Are My Questions:
1) Is There Any Real Chance That The Compression Differentials That The Mechanic Observed Were Caused By Something Simple Like A Spark Plug Malfunction, Which Got Worse During The Time That The Check Engine Light Was On? I Was Planning To Replace My Front Brakes Myself This Weekend Anyway So That It Could Pass The State Inspection. If Changing Out The Plugs And Wires Might Solve The Problem I Might Want To Give It A Try.
2) Is $800 To $1200 A Reasonable Amount To Charge For Rebuilding The Top Half Of An Engine? The Price May Or May Not Include Replacing The Timing Belt, Which I Think Should Be Right In The Area Anyway. The Belt Was Replaced 20,000 Miles Ago, But The Engine Has Been Leaking Oil For A While So There'S A Decent Chance It'S Been Splashed And Weakened.
3) Do Spark Plugs And Wires Normally Get Changed Out In A Rebuild Like This? I Imagine They Would Be Unless The Customer Asked, But I'M No Mechanic.
I Really Appreciate The Time You Guys On This Side Of Yahoo Answers Put In. Thanks For Reading Through My Questions.
When they do a compression check, they remove the spark plugs and check the compression that each piston is putting out. So, the plugs are not installed at the time.
Check around various other places for cost of rebuilding the top half, and also, maybe try another shop to get their diagnosis. I do not know what average cost would be. That price quoted would be about 10 to 14 hours labor, at $85 an hour avg. Plus the cost of gaskets, parts, etc. 10 Best Vehicle Service in Kingman Directory
Spark plugs should probably be changed out for new ones, during a rebuild. Wires, depends on how good they are now. Four good plugs run you about $10 or so. And depending on how old and worn the other parts are, like the water pump, it might be a good idea to replace it, if it is original.
But get a second opinion on repairs, unless it is too costly to do so. I know they charge for these diagnoses. Best Ten Vehicle Service in Kingman Directory
Standard Industrial Classification Code Most Popular Vehicle Service in Kingman Directory?
What Is An Automotive Repair Sic Code?
811111 General Automotive Repair
"This U.S. industry comprises establishments primarily engaged in providing (1) a wide range of mechanical and electrical repair and maintenance services for automotive vehicles, such as passenger cars, trucks, and vans, and all trailers or (2) engine repair and replacement." 10 Best Vehicle Service in Kingman Directory
Why Does My Engine Coolant Have What Looks Like Oil Droplets In It? I Have A 1991 Toyota 4-Runner 3.0 V-6?
Its A 1991 Toyota 4-Runner V-6 3.0, 4X4 Sr5 - (My Spare Vehicle) But I Use It To Camp And Hunt With - I Was Worried About What Engine Problems May Be Arising. I Am Mechanically Inclined And Do Many Repairs On My Own Vehicles, But This One Gets To Me A Bit - Thanks - Bp
1st off, without proper diagnostics you cannot get a proper repair...with that being said...
2nd it sounds like it could be a couple of different things,,,a blown head gasket or a cracked head or block (not likely though).
3rd, if it's not overflowing with oil and there isn't any water in your oil then let it go until you have more time and money to replace the gaskets. It is a time consuming job and while you're at it you might as well replace the timing belt/chain and gears(if necessary) as well as the oil/filter and anti-freeze because you're gonna have to take it all apart anyway.
Even in a large shop it averages about a day and a half to 2 days for this type of job. AND that's not including MURPHY'S LAW. This job can be done with the engine still in the car but it's much easier if you pull it completely out.
Good luck and hope this helps.
What Is The Need For Auto-Repair?
Can Anyone Give Me Some Links To Information On The Want/Need For Automotive Repair Or Automotive Customization In The Us Today?
Automotive repair is and will always (as long as vehicles are on the road) will be an ever expanding need, as for customization, that will always be a want but in the current economy will suffer due ot limited funds which will most likely go into the repair of said automobiles
Automotive Mechanic Vs Bachelor In Criminal Justice?
I Am Stuck Between These Two Careers For After I Graduate This Year. I Know I Will Make More Money In Criminal Justice, But I Don'T Know Much About The Program. So I Don'T Know If It'S Really Hard Or What? If I Go For Criminal Justice, I Want To Be A Border Patrol Agent, Or Something With Law Enforcement. I Know Some Bout Working On Cars, So That Career Won'T Be To Bad, But I Don'T Know If That Is What I Want To Do For The Rest Of My Life. Can Anyone Give Me A Little Detail On The Criminal Justice Degree? Thanks Alot!
Be warned that these are very specific degrees and with law enforcement you don't need a criminal justice degree to get a job working law enforcement. The difficulty of the degree depends on you and that particular program.
I've taken a number of courses in auto and criminal justice at the community college level and the automotive classes were fairly easy and so were the criminal justice classes. I knew nothing about cars though and I was taking them because my community college had a well known automotive program, especially for a community college, and I wasn't sure what I wanted to do. Both are great careers but also be warned that many cities have downsized their police with the economy. If you go with Criminal Justice also now that you will need to do a lot more then graduate to get a job in law enforcement. They will want to see a good work history, good driving record, good credit, you'll have to be in good physical shape, you'll need to pass a lie detector test, and more. I wouldn't be able to tell you about a criminal degree without a specific college in mind, but it will probably consist of courses like criminology, state law, etc. Really depends on the school. If you want to work border patrol I would also take Spanish, I would think it would help considerably.
1995 Ford Contour Problem?
We Bought The Car With A Blown Head Gasket. Fixed That And It Ran Fine For About A Year. Now It Runs Fine At Times And Won'T Seem To Fire At Times. Since It Runs At Times, The Timing Must Be Okay. It Seems To Have Spark And Fuel But Won'T Even Try, Then The Next Time You Try It Will Fire Up And Run For A While, Then Not Start Again.
get rid of it. joke it could be ignition module
1986 Bronco 2 Oil Leak?
I Have A 1986 Ford Bronco 2 With A 2.9 Liter V6. It Was Leaking Oil Pretty Bad So Me And My Friend Replaced Most Of The Gaskets (From The Head Gaskets And Up). I Thought That Much Would Fix The Oil Leak. Once I Got Done I Changed The Oil And Filter. But It'S Still Leaking Oil. Im Not Sure Where From Though. When It Is Running You Can See Engine Oil Leaking From Above The Oil Filter, Dripping Off The Filter And Its Dripping From The Transmission Pan. And Bellhousing.. So Could This Be The Rear Main Seal? Or What. Its Not Leaking From The Head Gaskets Or Any Of The Gaskets I Replaced. But It Does Look Like Its Leaking From A Little Bit Higher Than The Oil Filter. Anyone Got Any Ideas??
If I remember right there is a part that bolts to the block to adapt the filter location on the block. There is a O-ring that goes bad there. I used to know the part number, it is an obscure part that does not show up in most parts books.
Whats Going On With My Car If Its Over Heating And Dying When In Park? '95 Toyota 4Runner?
I Have A '95 Toyota 4Runner, And When I Start It Up, It Dies. Also, When I Start Giving It Gas It Starts To Over Heat. Any Ideas Of What Could Be Wrong?
Some of those 4Runners had weak head gaskets that might leak. Head gaskets leaking - coolant in the cylinders - may foul out the plugs on start up. When you get it running the exhaust gas leaks into the coolant and causes it to overheat. Run a compression test on it. On a 19 year old truck it could be almost anything - though.