Auto Repair in Lake Havasu

Home | Main Page | Advertise With Us | auto-repair-az-sitemap

In Case You Leave Auto Repair To A Professional Mechanic? Every car fails

Auto Repair in Lake Havasu Directory
at some time, and that's a fact! Having said that, some cars are very likely to malfunctioning than others, of course, if you're in a tough situation, you may be left to wonder: can i attempt a DIY auto repair or engage a mechanic? An oil change is a superb demonstration of something even a novice driver could do, but if you have troubles beyond that, acquiring a car mechanic to complete the repairs might be a good idea and here's why: Experience You may have absolutely no idea what you're doing and you could actually wind up making things worse. Even though you think that you're a DIY savvy person, you could end up causing other places of the car to malfunction. Not to mention, you only do not know what's actually wrong with your vehicle, until you accept it apart and hope with your might you can input it back together again again. A car mechanic continues to be doing this for many years and he can certainly diagnose and repair any issue your car or truck may be facing. Right Tools You will need the correct tools plus a decent workspace to begin focusing on auto repair. Unless you happen to have an entire garage with tools and equipment dedicated to this, you have got to purchase the desired tools to solve your automobile. Needless to say, without prior experience coping with car repair, you may not know what you must purchase, not to mention, you may never start using these tools again. Employing a Auto Repair in Lake Havasu Directoryprofessional car mechanic can eliminate the necessity for one to invest money into tools and equipment you're unlikely to make use of again because he will curently have everything on hand. Speedy Repairs Should you just have one household car you should utilize to access work with time, you have to be sure that the car is fixed at the earliest opportunity. Naturally, if you attempt a DIY repair, things can go wrong, and even after they don't, it takes you plenty more hours to get your automobile running than if you decide to engage a mechanic. You could have your automobile out of commission for a day or two when taking it to some mechanic, nevertheless it sure beats the inability to go to work! Spend Less Perhaps one of the more compelling top reasons to drop your automobile off for repair at a mechanic's is to save money. You won't have to invest money into tools, equipment, and auto parts you might never need. Not forgetting, while your car or truck is out of commission, you might want to rent an auto or take the bus-- costing you more money! Getting a mechanic for auto repair will save you inside the long haul, specifically if you take into consideration that a task well done can prolong the lifespan of your vehicle. The very next time your car or truck will give you trouble, why not stop at the car mechanic's?

Next_Page

Local Time in Lake Havasu | Wikipedia Information About Lake Havasu | Google Map of Lake Havasu
Youtube Video's of Lake Havasu | Info from Wiki on Auto Repair





DIRECTORY LISTINGS

G-N-G Automotive
, 23 reviews.
Auto Repair,Oil Change Stations
720 Lake Havasu Ave N, Lake Havasu City, AZ 86403
Bob's My Shop
, 16 reviews.
Auto Repair,Oil Change Stations,Tires
1950 Commander Dr, Lake Havasu City, AZ 86403
Accurate Auto Care
, 12 reviews.
Auto Repair,Towing
2950 Sweetwater Ave, Lake Havasu City, AZ 86406
Robinson Automotive
, 8 reviews.
Auto Repair
1640 West Acoma Blvd, Ste A112, Lake Havasu City, AZ 86403



FAQ's Auto Repair

Estimation For Car Rust Repair Best Ten Auto Repair in Lake Havasu Directory?
I Have A 1993 Dodge Intrepid. The Lower Door Skin On Both Side Has Some Rust Pretty Bad. Could You Guys Give Me A Range For The Cost Of Fixing This Problem. I Plan To Go To The Body Shop Cuz I Dont Know If I'm Able To Do It Myself. I Live Up North, And It Snows A Lot Here. I Gotta Think About Fixing This Car Before The Winter Comes. Also, Any Suggestion On The Rust Problem, I'd Be Appreciated Much. I'm Very New To Cars Generally. Thanks In Advance.

Before you considering repairing cosmetic rust, you should have the underside of the car inspected to be sure there is no rust that would adversly affect other areas like floorboards.

As far as repairing rust, it's not worth it unless you intend to move out of the rust-belt. Top Ten Auto Repair in Lake Havasu Directory

I worked with a guy in Long Beach, CA who repaired rust properly, which entails cutting out the rusted area and welding in an entirely new piece of sheet metal. He only repaired high end cars like '55 T Birds and Porsche Speedsters. If you asked him to repair the rust on your '93 Dodge, he would have counseled you against the idea.

Because the new sheet metal was welded in, it's not protected from rusting out again because it cannot be rust-proofed on the inner side. It rusts out even faster than the original metal did the first time.

The cheap way to repair rust is to bash in the rusted edge, mig in some metal in the general shape and bondo it over. This kind of repair leaves you with a real mess when the rusted metal that wasn't removed continues to rust out. 10 Best Auto Repair in Lake Havasu Directory

Generally speaking, people who have lived their whole life in the rust belt have their new cars undercoated, drive their older car in the winter and spring, and get more years out of the new car by only driving it in summer & fall and garaging it in inclement weather.

If you really want to go bargain basement, you can get some stainless steel tape at Pep Boys and apply it to the rust on your doors. But it won't look great.

I Have A 1999 Ford Contour...10 Best Auto Repair in Lake Havasu Directory?
I Am Having Some Mechanical Issues With My 1999 Ford Contour. I Was Driving To Work The Other Day And All Of A Sudden My Radiator Gauge, Battery Gauge And Oil Gauge All Came On (Which Has Never Happened Before). My Car Was Overheated And Out Of Oil (Which I Had Just Put A Quart Of Oil In A Few Days Earlier). When I Got To My Job (Barely Got There) My Car &Quot;Quit&Quot; On Me. But To Back Up Alittle The Symptoms It Was Having Was It Was &Quot;Ticking&Quot; And &Quot;Bogging Out&Quot; As I Was Driving. I Let My Car Sit For An Hour To Cool Down And Went To Check It Out. It Was Full Of Antifreeze But Barely Had Oil In It. Just A Tad Bit On The End Of The Dipstick. I Ended Up Putting In 2 Quarts Of Oil (Thinking It Might Of Been Just That). When I First Got To Work I Opened Hood And It Was Smoking From Engine Not The Radiator, By The Way. Anyhow I Left Work (Having To Travel 23 Miles To My Home) And Just Maybe 2 Miles (Or Less) My Car Did The Same Thing To Me. Ok So Here Comes The Question For You...What Do You Think It Could Be? My Mother Says Thermostat Or Vaccum Leak To Motor Or I Might Have A Blown Head Gasket? What Do You Think? I Am Having It Taken To Mechanic On Monday To Have It Put On The &Quot;Machine&Quot; To See What Is Wrong But My Car Has 160,000 Miles On It And I Really Do Not Want To Put Anymore Money In It. I Just Spent $600 On Brakes, Struts, And Miscellaneous Things. So Could You Give Me Ideas Of What You Might Think It Is?? Please!! Thank You So Much Top Ten Auto Repair in Lake Havasu Directory !

The ticking sound is caused by the lifters lacking oil. Some engines will shut down as self preservation when the oil pressure falls too low. You have a large oil leak. It could be worn piston rings or the PCV valve is faulty. Best Ten Auto Repair in Lake Havasu Directory

What Does It Cost To Repair A Blown Head Gasket?
I Blew A Head Gasket In My Engine, Is There Any Other Alternative For Fixing This Without Replacing The Gasket Top Ten Auto Repair in Lake Havasu Directory.

I have never seen so many questions about blown head gaskets. I have never had that problem nor run into it, and I got cars that date in the 50's and also got diesels(which must have 400 PSI+)
Gas cars new run 160 PSI. And compression goes down the longer you drive the car(engine wear)

You can't replace the head gasket unless you have a "torque wrench" and you know the torque and the tightening "pattern".

So, if you did it before by guesswork, guess you gotta do it again.(and again) 10 Best Auto Repair in Lake Havasu Directory

Once you compress a head gasket that is it for that gasket. There is no other option. Best Ten Auto Repair in Lake Havasu Directory

I Lost My Smog Check Certificate?
I Need To Do My Smog Check(State Of California), And I Have Lost The Certificate, What Should I? Can I Go And Do The Test Without Certificate Most Popular Auto Repair in Lake Havasu Directory?

You get the certificate AFTER the test, not before. If you lose the certificate showing your car passed smog, the DMV has it in their computer and so would Triple A. It's no problem.

If you lost the DMV paperwork they send you in the mail to get your smog, it doesn't matter either. Just tell whatever shop you go to you need a smog. They only ask for it to scan the VIN number, which is a lot faster than typing 17 numbers.

Looking For A Good, Low-Cost Mechanic/Shop To Work On My Audi A4. Any Recommendations For Anyone In La 10 Best Auto Repair in Lake Havasu Directory?

Low-cost and Audi don't go together. Here are some shops previously suggested by Audi and VW owners on the Internet:

http://www.advancegermancar.com/
http://www.eurotech-motors.com/
http://www.rennermotorsport.com/body.htm
http://www.eurasianautosport.com/
http://www.racesolutions.com/
http://www.stevesindependentvwaudi.com/
http://www.ingolstadtwest.com/
http://www.vwspecialties.com/

Tony's Auto Repair
9720 Atlantic Ave
South Gate, CA 90280
(323) 564-3361

Troy's VW and Audi Repair
11101 Ventura Blvd
Studio City, CA 91604-3134
(818) 752-9922
http://www.vwrepair.com/main.html

There are also people who have had problems at some of these shops.

Timing On A 99 Ford Contour Best Ten Auto Repair in Lake Havasu Directory?
I Am Having Issues With My 99 Ford Contour. We Have Replaced The Timing Belt, Head Gasket, And Had The Head Resurfaced And Valve Job Done. My Husband Has Set The Timing And To His Knowledge It Is Top Dead Center. The Problem Is That It Still Will Not Start. Everyone I Talk To Says That It Is The Timing That Is Still Off. If There Anything Else That Would Cause It Not To Start Or Is The Timing Still Not Right?

Both the crank and cam have to be at TDC - and depending on the vehicle it is possible to get it 180 degrees out of time. I always mark mine and am extremely careful not to move anything if at all possible).

When the timing belt tensioner is released it can often knock the system out of time - this can make it necessary to set it to slightly to one side or the other from TDC so that when it is released that it will pop up on TDC.

Since a lot of stuff had to be taken off the engine to take the head off for resurfacing and gasket replacement, it might be as simple as the crank or cam position sensor not being all the way plugged in (it is also easy to accidentally loosen a wire if you aren't careful unplugging various connectors). Most Popular Auto Repair in Lake Havasu Directory

I've been in exactly that position a few times - take it slow and check everything. It might not hurt to try giving the cam a 180 degree spin and trying it again just in case.

Career Change To: (Automotive Tech, Mechanic)?
Ok, Im Already 33 Years Old, I Worked In Banks All My Life And It'S An Ok Job. But I Am Tired Of It, Tired Of Seating On A Desk All Day With A Phone. I Want To Be An Automotive Technician (Mechanic) I Don'T Know Anything About Cars But I Love It. If I Could To A Training School And Get Just Basic Certification. Can I Start Working Right Away? Is It Hard To Get A Job Like That After Im Certified Or They Prefer People With Lots Of Experience.... Once Again, It'S Not Really The Money Or The Need Because I Make Ok Money Like 35K A Year But I Want A Big Change In My Life. Any Suggestions, Advices

I've been doing this for more than 30 years; automotive industry isn't what it used to be.
You have to keep up with ever changing demands, especially electronics, transmission, engines and drive-ability. You cannot afford to fall behind; if you do then you won't be making any money.

Right now it is bad time to become automotive technician.Nobody is making money. The economy isn’t that good and many people cannot afford to have their vehicles repaired.

There are few good Technical Schools but they aren’t worth a penny because I’ve seen student graduates from them and ‘expect” to make more than 18 dollars an hour, unfortunately, it doesn’t work that way. You have to start from the bottom and work your way up.
I've also seen them excel in tests and quizzes but failed miserably when it comes to fix the vehicles.
On top of that, many dealerships preferred technician that already has manufacture trainings, it is a lot more than basic certifications.

If you're GM certified tech, then good luck finding any job beside GM dealership. Ford won't hire you, Dodge won't hire you, and the list goes on and on or you can find a job in auto repair shop but most of them don't give you good pay and benefits.

Nowadays, good technicians are hard to find because most inexperience techs are just parts replacer, they really don't take their time and diagnosis any vehicle properly.
Example, Oxygen sensor codes, 99% of them [including internet expert] would simply replace oxygen sensor.
Good tech will interpret the code description and find out why and then fixed the problem.


Bottom line, good technician can easily make over 50k a year that because this particular tech has the will and motivation to keep up ever changing automotive industry.
If you have that attitude then go for it otherwise seek different job.


Good Luck.

Standard Industrial Classification Code?
What Is An Automotive Repair Sic Code?

811111 General Automotive Repair
"This U.S. industry comprises establishments primarily engaged in providing (1) a wide range of mechanical and electrical repair and maintenance services for automotive vehicles, such as passenger cars, trucks, and vans, and all trailers or (2) engine repair and replacement."

http://www.naics.com/censusfiles/ND81111...

How Do You Figure The Cubic Inches Of My Engine?
Ok I Have A Ford 460 In My 79 Bronco But Its Built Pretty Good And After A Recent Head Gasket Replacement I Checked The Bore And It Turns Out Its Bored 30 Over So What Does That Make My Cubic Inches?

that's why the online calculators are so nice..

Volume equals pie times the Radius squared times the stroke times the number of cylinders equals 467 rounded off.

that's using 0.030" over

Please Help What Is Wrong With My Car?!?
My Car Is A 96 Ford Aspire Was Running Fine A Few Days Ago Let My Sister Borrow It For A Night Comes Back Hardly Running Condition Im Not A Mechanic So I Have No Idea Whats Wrong With It....I Have A Youtube Video On What Its Doing Please Someone Help! Thanks A Ton Https://Www.Youtube.Com/Watch?V=Rwxnr3rscyi&Feature=Youtube_Gdata_Player

Your sister must have been hot dogging the car Driving it like a maniac. Looks like the head gasket is fried which mean your out some money rebuilding to top half of the engine Also your timing belt is fried or close to it, and oil is spewing all over the motor. You sister fried your motor From what it sounds like you rods or lifters are bad or bent a valve
which is in the head The tapping is the lifters or rods or values Either way its an top end rebuild 06 will be expensive
I would take it to a shop But I am pretty sure your head gasket is blown Can you drive it ? Well technically yes But only for absolute emergency because once it completely goes, your out a motor and cost is based on year The car might not be worth it This is the number one reason why I don't loan out my cars to friends or family EVER. Better start asking what your sister did besides cost you a 1000 bucks in engine repairs

Blown Head Gasket 95 Ford Bronco?
Ok So Here Is My Question? I Know I Have A Blown Head Gasket White Smoke Over Heating, Milky Oil Ect. How Much To Fix By Myself Or Have Someone Do It .I Can Do Miner Repairs To My Car I Just Have Never Had To Do This. Also How Long Will It Take And Can I Drive It To Go Get The Parts? I Really Don'T Want To Take It To Someone So If I Can Do It Myself Easily? Please Don'T Treat Me Like Helpless Female I Just Really Need Someone To Give Me So Figures.

It will cost you roughly 50 to 100 dollars depending where you get the parts, as for driving it to get the parts,I wouldn't go get the parts with it.You see when water gets in the main bearings, it can damage the entire engine and that can get expensive. To do the job yourself, you will need the Haynes or Chilton manual for the torque specifications of the head(s). You need a torque ratchet and about 6-12 hours of work time to do the job right,It'll save you about 200 dollars

Thermostat On A 97 Ford Aspire?
Where Is The Thermostat On A 97 Ford Aspire . Is It At The Bottom Of The Radiator Or At The Top ?

This you shall find behind the metal nozzle coming out of the cylinder head where the upper radiator hose mounts to the engine. It should be held inplace with 2 bolts. When replacing ensure that the old gasket has been throughly removed from both the head and the nozzle.
Install the new thermostat in the cylinder head, with the valve end first and the subvalve (air bleed valve) at the top.
Lightly coat both sides of the new gasket with gasket sealer.
New gasket and tighten the bolts to 15-19 ft lbs.