Maintenance Vehicles in Lake Havasu

Home | Main Page | Advertise With Us | auto-repair-sitemap

Next_Page

Local Time in Lake Havasu | Wikipedia Information About Lake Havasu | Google Map of Lake Havasu
Youtube Video's of Lake Havasu | Info from Wiki on Maintenance Vehicles

The Best Way To Effectively Tackle The First Big Auto Repair Job Now you know how to change oil inside your car, you may decide to handle


a much bigger auto repair task. Oftentimes, car enthusiasts decide to take a DIY method of car repair not just like a hobby, but as a way to spend less. In case your car keeps wearing down and you can barely pay for the parts to correct it, there's no method for you to pay money for professional labor. Before you tackle a big repair job, have a look at several of the expert advice below! Research First You can't take apart your car and aspire to use it back together again again if you don't know all of the parts. Unless you do have a very rare vehicle, it is possible to get ahold of your aftermarket manual for your personal model and make. These manuals can be really helpful in identifying the various components of the car and how they can be assembled. Not forgetting, there are simple to follow diagrams that will simplify this process. Aside from an actual manual, look to Internet forums for help. Odds are, somewhere in the world, someone has already asked exactly the same questions as you may. If you are stuck or there is a specific problem you can't wrap your mind around, post around the forums and request! Clear Workspace Area Focusing on an auto takes much more space than some individuals would estimate. You may think your garage has ample room, but you might be in for a rude surprise as soon as you start on the repair. It's better to clear lots of space and set up a workspace without additional clutter to create your work easier. Repair Will Take Time It's vital that you know that auto repair takes significant amounts of time and perseverance. In case the vehicle you wish to repair is the only ride to be effective, set up a carpool with a friend or find alternative transportation before taking your automobile out of commission. Be ready to make plenty of trips to a home improvement center and wait around for your car or truck parts ahead in, which can all require time. Keep Organized It's very easy to take something apart, nevertheless it could become a nightmare to set it back together again again. Once you have lots of nuts, bolts, and washers you're removing out of your car, it could feel as if an impossible task to keep in mind the way all goes together. Prior to taking your car apart, go on a photograph of how the parts look when properly installed. Once you've done that, label everything having a white pen and maintain them properly sorted in both plastic baggies or old egg cartons. Maybe you have lots of enthusiasm for auto repair, but be sure you shop around first, clear enough workspace, while keeping everything properly labeled. Many novice mechanics have learned that finding the time to generate a checklist will also help make a arena of difference! Should you stay organized and go in depth, it will be easy to correctly repair your first car.





FAQ's Auto Repair

1993 Toyota 4 Runner Wont Start?
So My 1993 Toyota 4Runner Has Been Running Rough For A Couple Days. Drove It Yesterday And Noticed It Was Overheating. Turned It Off And Had It Towed Home. I Filled It Up With Coolant (It Had All Leaked Out) And Checked The Rest Of The Fluids (No Water In The Oil). But Now It Wont Start It Just Cranks And Barely Fires. What May Be The Issue And What Should I Check. Any Help Would Be Great. Thank You

really, you need to determine how you lost all that coolant first. prolly point to the cause of the issue.
but,
me thinks you should suspect the worst.
pull plugs and see if they are fouled. prolly water foul. despite no water in oil. that would point to a water jacket/combustion chamber sealing issue for what ever reason.
at the onset, there maybe no signs of cross contamination of fluids and still have a bad head gasket.

i think you caught this relatively early. but if it is a head gasket, and this is a 3VZE V6, set some extra bucks aside for new timing belt and water pump. as the procedure for doing a head gasket will have those items exposed.
if this is a 22RE I4, get the timing chain assem inspected as well.

Smog Test Certificate Send To Dmv?
I Had A Smog Check Done The Men Who Did The Smog Test Said He Send The Smog Certificate Electronically To Dmv My Question Is Do I Still Need To Go To The Dmv And Give Them The Certificate Or Would The Registration Be Send To Be By Mail ?????? Thank You

You do not have to go to the DMV and you do not need a copy of the certificate. You do have to complete the registration process, but you can do it online. You do need to pay the registration fee to the DMV, but you can do that online also.

Car Help(Need A Good Mechanic To Answer Question)?
Hello, I Own A 1993 Toyota Camry Le With 117 K Miles And I Purshaced The Car In Late July With 114K Miles..Ever Since I Had The Car It Always Had A Rough Idle..I Put So Much Money Into It Trying To Figure Out What The Problem Was..New Timing Belt,Water Pump,Fuel Filter,Spark Plugs,Ignition Wires,Rotor,Distibutor Cap,Throttle Body Cleaning/Fuel Injection Cleaning,Alot Of Work And Still Did Not Find The Problem Of What It Could Possibly Be..Now Yesterday I Was Going About 40Mph Up A Hill And I Stopped To Turn..My Car'S Rpms Started Fluctuation Really Bad And It Stalled, I Smelled A Very Strong Burnt Smell For A Couple Mins..Then Tried Starting It Back Up And It Started Up Fine And Drove Fine.. But It Doesent Make Any Sence To Me..Please Let Me Know What Use Think Could Be The Problem.Thank You So Much

Locate and clean out your IDLE AIR CONTROL VALVE. It is near your throttle body. Use Gum-out spray, or AMSOIL foaming cleaner, if you can find it. Hopefully, this car has genuine TOYOTA coolant and not local parts store, green stuff. Over time, this coolant will eat holes through the head gasket and the aluminum alloy in the cylinder head, causing rough idling problems. You did the right thing by using a fuel injector cleaner (Techron is the best). Hopefully, you used NGK or DENSO spark plugs, and not el cheapos from the local auto parts store. Replacing wires and cap and rotor may have been a waste of money. If your distributor is mounted on the side of the engine (cam driven) remove the cap and rotor and spray the inside of it with brake cleaner. This will dislodge any oil sludge that may have wandered inside, a common trouble on these cars.This will stabilize the ignition. The burning smell that disappeared might mean that your alternator bearings or regulator are beginning to burn up. Get a free charging system test at AutoZone. Power wash your engine, especially around the battery terminals, and where they connect to the starter and chassis. Good luck!!

How Much Would It Cost To Overhaul An Engine Myself?
I Graduated From Universal Technical Institute And I Know How To Rebuild An Engine Pretty Well But Ever Since Before I Never Payed For Parts Because When I Was Younger By Dad Bought All The Parts And In School, The School Supplied All The Parts. Now, My Brother Has A 1997 Toyota Camry 2.2 L 4 Cyl. And I Want To Full Overhaul It From The Cams All The Way Down To The Crank. How Much Would All The Parts Cost Such As Bearings, Rings All The Seals Etc. .. I Just Need An Estimate

Assuming you will reuse the pistons, connecting rods, cam, crank and valves, you can expect to spend $600-700 for the other parts (rings, bearings, seals, head gasket, oil pan gasket, hoses, plugs, belts, etc. You'll also have the expense (unless you have the equipment to do it yourself) of sending the head, crank and cams to a machine shop to have the valve seats done, and the crank and cams to be micrometered to check for wear, and ground to fit over-sized bearings if needed. Expect to buy a few extra tools as well, such as a ring compressor, a cylinder hone, a good torque wrench, etc.

1995 Ford Contour Still Won'T Start?
I'M Stumped. I Have A 1995 Ford Contour Which Will Crank But Not Start. I Have Tried Re-Timing It, Using Starting Fluid, Checked For Spark, Installed New Spark Plugs, Checked Compression, Fuel Pump Primes With Good Pressure, Nothing Seems Bad. Compression Is As Follows: 1- 110Psi 2- 105Psi 3- 65Psi (The Bad One) 4- 80Psi (The Other Bad One) These Were Done With The Engine Cold, At Wide Open Throttle And Spark Plugs All Removed. I Put A New Head Gasket In It, So It'S Probably Just Blow By Causing The Low Compression. But It Still Should Start. Especially With Starting Fluid. It Ran Before The Head Gasket Went Out, Sat For 5 Months, Now After A New Gasket, Won'T Run. Timing Is Dead On. I Have Checked It 5 Times, Advanced It, Retarded It, Set It Dead On Too. It Does Sputter Like It Wants To Start, But Only With The Throttle Wide Open. I Removed The Fuel Pump Relay, And Tried Starting It With Starting Fluid Only Also But It Just Sputters. So It'S Not Flooded Either. The Cylinder Looks Wet But Only After Reinstalling The Relay. It Seems Like Timing, But It'S Dead On. (I Replaced The Head Gasket 11Mos Ago Too And It Ran Fine. Any Help Would Be Appreciated.

Double check that the Cam is in the correct position. Your crank timing might be on, but if the cam is even just one tooth off it can cause the motor to not run.

Cooling System On 98 Ford Contour 2.0 Is Not Working. ?
Replaced Thermostat And Radiator Fan - Both Working. Car Gets To Hot After About 7 Miles Of City Driving. A/C Begins Blowing Hot Humid Air After ~3 Miles. All Fluid Levels Are Good. Turning On Heater To Blow Off Hot Air Does Not Help. Water Pump Replaced Last Year When Timing Belt Broke.

check the oil to see if it has a milky color to it, like from the coolant mixing with the oil, if thats the case you most likely have a blown head gasket.

A blown head gasket is the single most causes of overheating