Should You Really Leave Auto Repair To A Professional Mechanic? Every car stops working
at some time, and that's a well known fact! With that in mind, some cars are very likely to malfunctioning than the others, and when you're inside a tough situation, you may well be left to wonder: should I attempt a DIY auto repair or employ a mechanic? An oil change is a good demonstration of something a good novice driver could do, but if you have troubles beyond that, getting a car mechanic to perform the repairs could be a great idea and here's why: Experience You possess simply no idea what you're doing and you can actually turn out making things worse. Although you may feel as if you're a DIY savvy person, you could potentially find yourself causing other regions of the car to malfunction. In addition to, you simply have no idea what's actually wrong together with your vehicle, except if you take it apart and hope with all your might you are able to use it back together again. An auto mechanic has been doing this for several years and that he can easily diagnose and repair any difficulty your car may be against. Right Tools You want the proper tools as well as a decent workspace to begin concentrating on auto repair. Except if you have a whole garage with equipment and tools committed to this, you need to invest in the essential tools to fix your vehicle. Naturally, without prior experience working with car repair, you possibly will not know what you need to purchase, in addition to, you may never begin using these tools again. Getting a professional car mechanic can eliminate the demand for one to invest money into tools and equipment you're unlikely to use again as he will have everything on hand. Speedy Repairs Should you just have one household car you need to use to reach focus on time, you have to be sure that your car is fixed without delay. Needless to say, when you attempt a DIY repair, things could go wrong, and even after they don't, it takes you plenty more time to get your car running than if you decide to employ a mechanic. You could have your car out of commission for a day or two when taking it to a mechanic, but it sure beats being unable to go to work! Spend Less Perhaps one of the more compelling good reasons to drop your vehicle off for repair with a mechanic's is to economize. You won't must invest money into tools, equipment, and auto parts you might never need. Not forgetting, while your car has run out of commission, you might have to rent a car or take the bus-- costing you even more cash! Working with a mechanic for auto repair could help you save within the long term, specifically if you take into consideration that a job well done can prolong the life of the vehicle. Next time your car or truck will give you trouble, why not stop at a car mechanic's?
Local Time in Lake Havasu |
Wikipedia Information About Lake Havasu |
Google Map of Lake Havasu
Youtube Video's of Lake Havasu |
Info from Wiki on Mercedes Repair
FAQ's Auto Repair
Could There Be More Problems With This Ford Bronco Best Ten Mercedes Repair in Lake Havasu Directory?
Tomorrow I Am Going To Look At A 1989 Ford Bronco That A Guy Was Advertising On Craigslist. I Called Him And He Told Me That The Only Problems It Has Are A Mistimed Ignition And It Needs A Couple Freeze Plugs Replaced.
Basically I Need To Know If It Could Possibly Have Worse Problems That He Is Trying To Pass Off As These Less Serious Ones. What Should I Look For?
Yes, very well have more problems, with ign off as he claims could use this to hid compression problems and timing chain issues, freeze plugs could hide head gaskets or other things that make it overheat. But he could be shooting straight, most times people selling cars don't. 10 Best Mercedes Repair in Lake Havasu Directory
How Do You Figure The Cubic Inches Of My Engine?
Ok I Have A Ford 460 In My 79 Bronco But Its Built Pretty Good And After A Recent Head Gasket Replacement I Checked The Bore And It Turns Out Its Bored 30 Over So What Does That Make My Cubic Inches 10 Best Mercedes Repair in Lake Havasu Directory?
that's why the online calculators are so nice..
Volume equals pie times the Radius squared times the stroke times the number of cylinders equals 467 rounded off. 10 Best Mercedes Repair in Lake Havasu Directory
that's using 0.030" over
Ford Contour 99, Runs Very Bad. Best Ten Mercedes Repair in Lake Havasu Directory?
I Have A Ford Contour 99, I Did Replace The Timing Belt, Idler Pulley, And Timing Adjuster. Now After That It Run A Little Rough, So I Decided To Use For Some Time, Now Is Worse, I Did Re-Set Timing Following Ford Instructions, 1 And 4 Cylinder At Tdc, Cams Aligned With Flat Steel Tool, Cam Sprockets Loose, Timing Belt Tight All The Way Around, Re- Started And Runs Very Bad, Shakes, Misses, All Kinds Of Things. No Smoke At Tailpipe, Then I Checked The Compression, It Was Very Low, Almost Cero.. My Question Is: Can My Timing Be Off To Not Having Any Compression At All≫? Or Could I Have A Burned Valve, Or A Piston/Valve Collision, (Acording To Ford,Is Not An Interference Engine,[2.0 Liter] ) Any Suggestions≫?, I Almost Throwing My Towel, And Don'T Know What Can Be The Problem.. Did Replace Sparks, Coil, Sparks Cables, Checked My Injectors, No Vacuum Leaks, Thank You For Any Good Help.
A stock Zetec is non-interference unless it's a SVT or has been modified (high lift cam). If the timing is way off, then you won't have compression, but it sounds like you are doing it right from what I can gather. However, in some cases non-interference engines can get bent values due to carbon buildup on top of the cylinders, especially in the valve reliefs (reduces valve clearance). There are some rare cases of this occurring with the Zetec.
To test the valves, you can do a leak down test on the cylinders. Basically you shoot compressed air in through the spark plug and see if the pressure in the cylinder drops. In your case, if you have bent valves you should be able to hear a decent "hiss" in the intake or exhaust. You can also try testing the compression with the timing belt off and both valves closed (rotate camshafts). Best Ten Mercedes Repair in Lake Havasu Directory
Burnt valves are also a possibility, but you would have noticed this before the belt change. It is also unlikely all four would be burnt and giving zero compression.
Just to be sure, cylinder #1 is the one closest to the timing belt. Also, did you double check your plug wiring? Try to be as precise as possible with TDC in #1, otherwise you could be a tooth or two off.
You said no vacuum leaks, but did you check the EGR, IAC, and MAF? These can all cause roughness.
If all else fails, you can pull the head and see what it looks like inside. Might as well replace the head gasket (order after you see the condition of the valves).
Here is another how to, maybe a different source will help: http://www.contour.org/ceg-vb/showthread...
Hope you can figure it out! Best Ten Mercedes Repair in Lake Havasu Directory
Car Issues...Blown Head Gasket And Antifreeze Leak 10 Best Mercedes Repair in Lake Havasu Directory?
I Have A 1997 Ford Contour Gl With Almost 112Kmi. Last Week When I Was Driving The Car At 55 Mph The Car Started Lurching Forward...Kind Of Like How It Feels When You Just Tap On The Accelerator And It Jumps Forward. I Pulled Over And Turned The Car Off To Check For Leaks And A Flat Tire, Nothing Happened. Went To Turn The Car Back On (Worked) And Started Driving Home...Which Was About Half A Mile. As Soon As I Started Driving (20 Mph) The Front Of The Car Started To Shake Really Bad (Is Not The Alignment), Made Groaning And Whaling Noises, And Would Not Accelerate Above 25 Mph. When I Finally Made It Home I Turned Off The Engine, Went To Call My Mechanic, And He Told Me To Turn It Back On But It Wouldn'T Start. I Have To Wait Two More Days Until I Can Get The Car Looked At But In The Mean Time I Tried To Jump Start The Car To See If It Would Start. It Took About 3 Tries And Then Just Letting The Car Charge From My Moms Car And It Finally Worked. Now The Car'S Exhaust Is Spewing White And The Antifreeze Is Brown/Rusted But Not Too Low. It'S Also Idling Really Rough And Over Heats Within A Minute. I Have Never Missed An Oil Change, So That Isn'T The Issue. I Also Have An Over Heating Issue And My Temp Gauge Isn'T Registering It (I Think That'S Just Broken). I Just Want To Know If Anyone Else Has Had This Issue Or Knows What It Could Be. I'Ve Been Told It May Be A Blow Gasket And An Antifreeze Leak Into The Oil. Wanted Some Opinions Before It Gets Looked At In 2 Days. I'M Trying To Figure Out If It Is Too Bad A Fix And If I Should Just Get A New Car. Please Do Not Answer This If You Have No Intention On Giving Me Advise For What May Be Wrong With The Car.
yes sounds like the head gasket but also could be the intaake manifold gasket and my advise is to buy a new car 10 Best Mercedes Repair in Lake Havasu Directory
What Should I Do With My Car Best Ten Mercedes Repair in Lake Havasu Directory?
I Asked A Question Not Too Long Ago About My 1997 Ford Aspire With 121K Miles, Which Had A Misfire In One Of Its Cylinders When I Bought It. Now I'Ve Got Several More Questions. Here'S The Story:
I Took It To A Reputable Repair Shop And Had It Diagnosed The Other Day As A Pretty Serious Problem, Which Was Most Likely A Malfunctioning Valve, Though They Would Have To Take Apart The Cylinder Head To Confirm That. They Based Their Evaluation On The Fact That The 3 Healthy Cylinders Were Putting Out 170 Pounds Of Pressure While The Other Was Putting Out 80 Pounds. When I Talked To Other Mechanics They Said They Would Expect A Valve Problem Too With Those Numbers. I Have An Appointment Set For Monday Morning To Get The Cylinder Head Taken Off So That The Mechanics Can Find Out What The Problem Is Exactly.
The Previous Owner Knew For Some Time That The Misfire Existed, But He Assumed That It Was Because Of The Spark Plugs, Which Are Pretty Worn. After I Bought The Car And Drove It Around A Bit, But Before I Took It To The Mechanic, The Check Engine Light Came On And Remained On Until Earlier Today When It Shut Off.
Here Are My Questions:
1) Is There Any Real Chance That The Compression Differentials That The Mechanic Observed Were Caused By Something Simple Like A Spark Plug Malfunction, Which Got Worse During The Time That The Check Engine Light Was On? I Was Planning To Replace My Front Brakes Myself This Weekend Anyway So That It Could Pass The State Inspection. If Changing Out The Plugs And Wires Might Solve The Problem I Might Want To Give It A Try.
2) Is $800 To $1200 A Reasonable Amount To Charge For Rebuilding The Top Half Of An Engine? The Price May Or May Not Include Replacing The Timing Belt, Which I Think Should Be Right In The Area Anyway. The Belt Was Replaced 20,000 Miles Ago, But The Engine Has Been Leaking Oil For A While So There'S A Decent Chance It'S Been Splashed And Weakened.
3) Do Spark Plugs And Wires Normally Get Changed Out In A Rebuild Like This? I Imagine They Would Be Unless The Customer Asked, But I'M No Mechanic.
I Really Appreciate The Time You Guys On This Side Of Yahoo Answers Put In. Thanks For Reading Through My Questions.
When they do a compression check, they remove the spark plugs and check the compression that each piston is putting out. So, the plugs are not installed at the time.
Check around various other places for cost of rebuilding the top half, and also, maybe try another shop to get their diagnosis. I do not know what average cost would be. That price quoted would be about 10 to 14 hours labor, at $85 an hour avg. Plus the cost of gaskets, parts, etc. Most Popular Mercedes Repair in Lake Havasu Directory
Spark plugs should probably be changed out for new ones, during a rebuild. Wires, depends on how good they are now. Four good plugs run you about $10 or so. And depending on how old and worn the other parts are, like the water pump, it might be a good idea to replace it, if it is original.
But get a second opinion on repairs, unless it is too costly to do so. I know they charge for these diagnoses. Most Popular Mercedes Repair in Lake Havasu Directory
Standard Industrial Classification Code Top Ten Mercedes Repair in Lake Havasu Directory?
What Is An Automotive Repair Sic Code?
811111 General Automotive Repair
"This U.S. industry comprises establishments primarily engaged in providing (1) a wide range of mechanical and electrical repair and maintenance services for automotive vehicles, such as passenger cars, trucks, and vans, and all trailers or (2) engine repair and replacement." Top Ten Mercedes Repair in Lake Havasu Directory
Why Does My Car Keep Burning Off The Oil?
I Drive A 2002 Toyota Avalon And Theres About 116,000 Miles On It. The Previous Owner Was My Mother So I Know Where It Came From. The Biggest Physical Sign That Tells Me Something Is Wrong Is That It Burns Through It'S Supply Of Oil Before It Should And It Smokes When I Cold-Start It. I Got An Oil Change 2 Months Ago, And I Put One Quart Of Oil In It About A Month Ago. I Went To The Oil Changing Place Two Days Ago To Have My Fluids Topped Off And They Had To Put In 3-4 Quarts Of Oil. More Often Than Not, A Big Cloud Of Smoke Will Come Out Of The Exhaust If It Hasn'T Been Started In A While, Especially If It'S Warm Outside. It'S Not Leaking Any Oil And There Doesn'T Seem To Be Any Other Problems As Far As I Can Tell. It'S Been Given A Once-Over By A Mechanic A While Ago But I Don'T Think He Looked Hard Enough.
Can Anyone Think Of What It Might Be? Solutions??
Ouch. My 01 Camry puffs a little bit when I start it cold in the mornings. If your car is using that much oil in such a short period of time, here are some things to consider:
Your oil seals could be worn out. This can come from sitting still for a long time or being hard on the car.
You could have a cracked head or head gasket. Is there oil in your antifreeze, or antifreeze in you oil? (Can't remember which it is)
Has your car overheated?
Either way, its not gonna be a cheap fix unless you know what you're doing and can handle the job yourself. That engine's on it's last leg.
Factory Rebuilt 3Vze For 92 Toyota Pickup 4X4. Good To Go?
So I Love The 89-95 Toyota Ext Cab 4X4 Pickup. Most Of The Few I've Seen For Sale Are Equipped With The Infamous 3Vze 3.0 6Cyl. One In Particular Has Low Overall Miles And The Engine Was Rebuilt By Toyota On The Factory Recall. Once Rebuilt, Are These Engines Good To Go, Or Do You Stand The Same Chance Of A Blown Head Gasket That You Did Before? I Know The 22R Was Better, But That's Not My Question. I Want To Know How Reliable One Can Expect This Engine To Be. It Has 140K Miles And Was Rebuilt 30K Miles Ago (Obviously Hasn't Been Driven Much Since Then).
well for the 3.0 3vze, i found a few articles on this question,
this article deals with alot of people talking about how long there 3vze lasted before and after the head gasket problem.
and this other article is
"I'll take the 22re AND the 3vze!
I think the 3vze is one hell of a reliable engine. Significantly more reliable than other manufacturers of the era these engines were produced. The 22RE is also a reliable engine - more reliable than the 3vze? I don't think so.
The one hindering thing with the 3vze that lots of mostly non owner "theorists," seem to like to point out when debating the merits of the 3vze vs 22RE or other engines they think they know well is the headgasket problem. But I think something needs to be made very clear about the head gasket "problem." First, it is not a Problem. The headgasket put in these vehicles at the factory was the WRONG head gasket. Wrong in terms of design, or material, probably a bit of both. When Toyota put the Right head gasket in, either with the last year (95) of the 4runner/pickup with the 3vze, or through the recall, the 3vze is every bit as reliable as the 22re. If they were just replacing the head gasket during the recall with the same one they put in the factory when the truck was built, and the recalled head gasket wasn't holding up, then it would be a problem. But the redesigned proper headgasket holds up, so it is not a "problem." Calling it a problem would insinuate that it reptitively occurs in this truck. But it is clear that it does not. It may have happened once - with the original head gasket if the dealer didn't get to it first with the recall, but when it's taken care of, it's taken care of. People seem to forget that the 22re has a skeleton on the closet in the timing chain. This slight flaw can also be fixed by changing the timing chain more regularly (i.e. paying attention to its maintenance) or buying metal timing chain guides over the stock plastic ones. But when both of these flaws are addressed with the fixes available, these engines are simply flawless! (if that makes any sense)." CoedNaked-yotatech.com
Originally Posted by CoedNaked
"But when both of these flaws are addressed with the fixes available, these engines are simply flawless! (if that makes any sense)."
You seem to have forgotten the issue of the #6 exhaust valve burning. The cure for that seems to be elimination of the crossover, headers, and exhaust. People have had the recalled HG fail so it can still be an issue/problem. It also seems that more people have problems with the 3vze than the 22re on this board.
I like the 22re better for these reasons:
1. More reliable.
2. Better gas mileage.
3. Much easier to work on. If the HG goes (which does happen every once and while), you can easily fix it yourself.
4. More and cheaper aftermarket parts. You can easily and cheaply build a reliable 22re with the same amount of power as the 3vze. Intake, cam, header, and exhaust is all you need.
5. Relatively the same amount of power with the 5-speed when the 3.slow has the auto behind it (or so I'm told).
6. Much cheaper to replace.
I would much rather prefer to have the 22re and do some mods to it. It's just an overall better engine without the design flaws of the 3.slow. If my motor goes, it's getting a swap but probably not for a 22re. If I'm going to go through that trouble, I'm getting power.
EDIT: Replacing the timing chain guides is very minor and inexpensive compared to a HG on the 3vze.
10 Advantages Of An Auto Mechanic And 10 Disadvantages?
A mechanic can fix it much faster than the average joe.
A mechanic has the proper tools to do the job right.
A mechanic wasn't riding in the car when it made that noise
You may give up, or not know how to proceed if you break a stud off.
A mechanic may know tricks of the trade that makes jobs much easier.
You may break more than what's wrong.
You may spend more by using the shop & swap method of diagnosing problems.
You may not have the correct tools for the job
You may get to know your car better by working on it yourself
You can keep track better of what needs maintenance if you look at it often
You can rely on the mechanic's judgement of what else needs replacing if he's doing the work.
You can judge what else needs replacing if you have the experience.
You can save a lot of money by doing the car repairs and maintenance yourself.
You usually won't forget to fill the engine with oil, and won't drive it a mile with the light on if you're mechanically inclined.
What Is Automotive Mechanic Tools?
Myself John Lee,If Anyone Know More Information About Automotive Mechanic Tools Please Suggest Me.
the tools auto mechanics use to work on cars . get on website snap on tools.com or just walk into a sears store and you'll see what a wide selection there is
How Much Should A Smog Test Cost?
I Have To Get A Smog Certificate From A &Quot;Test Only&Quot; Station As Part Of My California Registration Renewal. I Have Been Getting Various, Inconsistent Prices From Different Businesses.
The new Smog Check 2 equipment costs $50,000 and the state charges $8.25 for a smog certificate.
All smog checks are NOT equal. Compare our procedures with others.
Other Smog Stations
No extra charge EXTRA Charge of $5 to $10
bullet Electronic Transmission
NO extra charge EXTRA Charge of $3 to $5
bullet OBD II, 1996 & Newer Vehicles
NO extra charge EXTRA Charge of $5 to $10
FREE Only free if they do repairs
bullet No DMV Papers
FREE EXTRA Charge
I Have A 1991 Camaro With A 305 And A Toyota Supra 3.0 They Both Busted The Radiators Wide Open Under Pressure?
Both Cars Got Really Hot Over 260 And The Busted The Radiators Wide Open, Are The Head Gaskets Blown?
In addition to the first post, you can use a compression tester or leak down gauge to pump air into each cylinder listening for air leakage with both valves closed. Check for water in the oil, and also oil in the water.
Keep in mind with the 305 at least, that the heads are prone to cracking when the engine is over heated.